Photo to STL converter
Turn a photo into a printable lithophane — a flat print whose thickness follows the picture, so it appears only when you hold it up to the light. Built in your browser, exported in real millimetres.
No image loaded yet. Your picture is read by this browser tab and never sent to a server.
Pick an image to start. Nothing is uploaded.
Drag to rotate - scroll or pinch to zoom - right-drag to pan
Your image is read by this browser tab only. Nothing is uploaded, nothing is stored, and no account is required.
What you get
A lithophane is a flat print whose thickness follows the brightness of a picture. Held up to a lamp it turns into a photo; held up to daylight it looks like a blank sheet of white plastic. Because the picture is in the geometry rather than the colour, it prints on a single-colour printer and still looks like a photograph.
Set the mode to Lithophane, then choose the printed width. 100 mm is a comfortable size for a face; 150 mm is a framed portrait. The depth slider sets how much thicker the darkest part is than the lightest, and 3 mm is the value that works with the widest range of filaments.
Preparing the photo
Crop to the subject before loading it — you cannot crop the mesh later without rebuilding. Photos with a bright background and a mid-tone subject convert best, because a lithophane needs contrast to read. If your photo is flat, raise contrast a little in any editor first. Small faces on a wide shot will lose detail; crop in until the face fills a third of the frame.
A colour photo is fine: brightness is computed with the standard luminance weights, so reds and blues do not disappear.
Print settings for a lithophane
- Stand the model upright, not flat. Vertical layers make the light gradients smooth.
- 100% infill, no top or bottom skin gaps.
- 0.12 mm layers; 0.08 mm if your printer is well tuned.
- 3 perimeters and white or natural filament — coloured filament casts a tint over the whole image.
- A 3 mm brim helps tall thin frames stay stuck, but do not use a raft.
Common problems
Washed out and grey. The depth range is too small. Raise the depth slider toward 3.5 mm and rebuild.
Too dark, no highlights. The source photo is underexposed. Brighten it before converting, or tick invert if the image was already inverted.
Visible staircase on skin. Raise detail to 200 px. Below about 120 px a face starts to look carved rather than photographed.
It fell over mid-print. Add a 2 mm frame in your slicer, or print slower on the first 20 layers.
Photo to STL, not photo to 3D
This page makes a relief solid, not a reconstructed head. If you want a figurine from a photo, a relief will not satisfy you and a reconstruction model is the right tool. If you want a gift that shows the photo exactly, nothing else prints this well on a hobby printer.
When you are done, the image to OBJ page exports the same mesh as OBJ for sculpture software, and the 2D to 3D guide covers the difference in more depth.
Questions
What filament is best for a lithophane?
White PLA is the default choice because it diffuses light evenly. Natural and clear filaments work too. Black or coloured filament absorbs too much light and the image turns muddy.
How long does it take to print?
A 100 mm wide portrait at 3 mm depth takes roughly 25–40 g of PLA, about four to six hours on a stock 0.4 mm nozzle at 0.12 mm layers.
Do I need to upload my photo?
No. The photo is decoded and the mesh is built in your browser tab. Nothing is uploaded and the file is created locally.
Can I use a black and white photo?
Yes — tick the invert box and rebuild. Inverting swaps which end of the brightness range becomes thick, which is exactly what you want for negatives, x-rays and night shots.
How thin can the lightest areas be?
Around 0.8 mm. Anything thinner will not survive the first layers. The converter keeps a 0.6 mm floor plus a 0.4 mm base so the mesh never goes below what a 0.4 mm nozzle can lay down.
Other converter modes
PNG to 3D model
Plaque mode: a transparent PNG becomes a raised cut-out on a solid base.
Open plaque mode →Image to OBJ
Relief mode with OBJ export, for software that prefers OBJ over STL.
Open relief mode →AI image to 3D
Need the actual object, not a relief? The AI mode reads the photo, builds a closed mesh and previews it in 3D.
Open AI mode →